When you need square footage
Square footage is the number behind most home decisions: how much flooring, tile, carpet or paint to buy, what a contractor will charge, how big a home really is, and whether a rug or piece of furniture will fit. Getting it right saves money twice: you avoid ordering too little and paying for a second delivery, and you avoid paying for material you don’t need.
How to use the calculator
- Choose the unit you measured in: feet, inches, yards, meters or centimeters. The square footage calculator converts everything to square feet, and also shows square meters, square yards and square inches.
- Pick the shape of the first area and enter its measurements.
- For an L-shaped or irregular room, tick Add a second area (and a third if needed) and enter each section separately.
- Optionally, enter a price per square foot, for example a flooring quote, to get an estimated cost.
Area formulas
Rectangle or square: area = length × width Circle: area = π × radius² (radius = diameter ÷ 2) Triangle: area = base × height ÷ 2 1 sq ft = 144 sq in 1 sq yd = 9 sq ft 1 ft = 0.3048 m exactly 1 sq ft = 0.09290304 m² 1 m² ≈ 10.764 sq ft
For a triangle, the height is measured at a right angle from the base to the opposite corner, not along the sloping side.
Worked examples
A rectangular living room
12 ft × 15 ft = 180 sq ft, which is 16.72 m² or 20 sq yd.
An L-shaped room
Split the L into two rectangles that don’t overlap: a main section of 12 ft × 15 ft and a nook of 8 ft × 6 ft.
180 sq ft + 48 sq ft = 228 sq ft.
A round patio
Diameter 10 ft, so radius 5 ft. Area = π × 5² = 3.1416 × 25 ≈ 78.54 sq ft.
Measured in inches
A bathroom floor 96 in × 60 in = 5,760 sq in. Divide by 144: 40 sq ft.
How to measure a room accurately
- Measure wall to wall at floor level, where the flooring will go, not at waist height.
- Measure each wall. Older rooms are rarely perfect rectangles. If opposite walls differ, use the longer measurement so you don’t come up short.
- Round up to the next inch rather than down.
- Sketch the room and mark each measurement. For odd shapes, draw lines that split the floor into rectangles and triangles, then measure each piece.
- Include doorways and closets that will get the same flooring, and leave out areas under built-in cabinets or kitchen islands.
Turning area into materials
Square footage is the starting point, not the order quantity. Flooring and tile are cut to fit, and some pieces are wasted at walls, corners and doorways. You will usually order your square footage plus a waste allowance, then round up to whole boxes. The tile calculator does this for you, including grout gaps and tiles per box.
Paint is different: it covers wall area, not floor area. To estimate wall area, multiply the perimeter of the room by the wall height, then subtract large openings such as doors and windows. Check the coverage printed on the paint can to see how many square feet each gallon covers.
Countertop square footage
Countertops are usually measured in inches, so measure the length and depth of each run, multiply, and divide by 144. A run 96 inches long and 25.5 inches deep is 96 × 25.5 = 2,448 sq in, or 17 sq ft. Measure an L-shaped counter as two rectangles that don’t overlap, and add backsplashes as their own rectangles (length × height). Choose inches as the unit above and the calculator does the division for you.
Roof square footage
A pitched roof has more surface than the floor beneath it. To estimate it, multiply the footprint (including overhangs) by a pitch factor:
pitch factor = √(1 + (rise ÷ 12)²) roof area ≈ footprint × pitch factor
For a 6/12 pitch (6 inches of rise per 12 inches of run), the factor is √1.25 ≈ 1.118. A 1,500 sq ft footprint becomes about 1,677 sq ft of roof. Roofers often quote in “squares”, where one square is 100 sq ft, so that roof is about 16.8 squares before waste. Roof measurement on a steep or complex roof is best left to a professional.
Acres to square feet
Land is often measured in acres. One acre is 43,560 square feet, so a 0.25-acre lot is 10,890 sq ft. The calculator shows the acreage of any area you enter, which is useful for lawns, gardens and lots. To enclose a lot, the fence calculator counts the posts, rails and pickets for the perimeter.
Cost per square foot
Contractors and stores often quote flooring and installation per square foot. Enter that price in the calculator to estimate cost. Remember that quotes may or may not include materials, underlayment, removal of old flooring, trim and waste. Ask exactly what is included so you can compare quotes fairly.
Square footage of a home
For a whole house, the “living area” in a listing is usually the finished, heated space, measured from the outside of exterior walls. Garages, unfinished basements and porches are usually listed separately. Methods vary by market, so treat listing figures as a guide and measure yourself for project planning. If you are buying, the mortgage payment calculator helps you turn a price into a monthly cost.
Frequently asked questions
How do you calculate square footage?
Measure the length and width of the space in feet and multiply them. A 10 ft by 12 ft bedroom is 10 × 12 = 120 sq ft. For irregular spaces, divide the area into rectangles, triangles or circles, work out each one, and add them together.
How is square footage calculated?
Square footage is an area: the number of 1 ft × 1 ft squares that fit in a space. For a rectangle it is length × width, for a triangle base × height ÷ 2, and for a circle π × radius². Measurements must be in feet first, or converted to feet (divide inches by 12).
How do you calculate the square footage of a house?
Sketch the floor plan, split each floor into rectangles, multiply length × width for each, and add everything together. Listings usually count finished, heated living space and list garages, unfinished basements and porches separately, but measurement standards vary by market, so check how a listing figure was measured.
How do I measure in inches and get square feet?
Multiply length × width in inches to get square inches, then divide by 144 (because 1 sq ft = 12 × 12 = 144 sq in). Or select inches as your unit in the calculator and it converts for you.
How many square feet are in a square meter?
One square meter is about 10.764 square feet, and one square foot is 0.092903 square meters. One square yard is exactly 9 square feet.
How do I calculate the area of a circular space?
Measure the diameter (the distance straight across through the center), halve it to get the radius, and use π × radius². A circle 10 ft across has a radius of 5 ft and an area of about 78.54 sq ft.
Do I subtract areas such as kitchen islands or closets?
For flooring, measure only the floor you will actually cover. Leave out permanent fixtures such as built-in cabinets or islands, but include closets if you are flooring them. Then add a waste allowance when you order materials.